CIR06AF-36-5S vs CTV07RF-9-9SA-S25
| Part Number |
|
|
| Category | Circular Connectors | Circular Connectors |
| Manufacturer | ITT Cannon, LLC | Amphenol Aerospace Operations |
| Description | CONN PLUG 4POS STRGHT SKT | CONN RCPT FMALE 9POS GOLD SLDR |
| Package | - | - |
| Series | MIL-DTL-5015, CIR | MIL-DTL-38999 Series III, Tri-Start? HD |
| Features | Cable Clamp | Shielded |
| Mounting Type | Free Hanging (In-Line) | Panel Mount, Bulkhead - Front Side Nut; Through Hole |
| Termination | Solder Cup | Solder |
| Current Rating | 150A | - |
| Voltage - Rated | 500VAC, 700VDC | - |
| Contact Finish | Silver | Gold |
| Orientation | N (Normal) | A |
| Number of Positions | 4 | 9 |
| Connector Type | Plug, Female Sockets | Receptacle, Female Sockets |
| Shell Size - Insert | 36-5 | 9-9 |
| Fastening Type | Bayonet Lock | Threaded |
| Shell Material, Finish | Aluminum Alloy, Olive Drab Cadmium Plated | Composite, Nickel Plated, Electroless |
| Ingress Protection | - | Environment Resistant |
-
1. How to cnlinko 4 pin power industrial circular connector
1. Confirm the voltage, current and frequency:
2. Choose the right environment: In normal environment, regular plugs and sockets can be used. IP67 anti-immersion plugs and sockets are used in harsh environment.
3. Pay attention to the installation of the connector: Make sure that the socket used to install the connector on the power supply line has a cover to prevent electric shock.
4. Check the connector status: Before use, check whether the model, code, number, plug position and direction of the connector meet the requirements of the design and process documents. 5. Correct plugging and unplugging operation: Before plugging, check whether the code, interface, etc. of the plug to be plugged in correspond to the socket, and accurately position them. -
2. How to solder a circular connector
1. Remove the insulator, prepare the soldering iron and needle-nosed pliers or tweezers;
2. Place the blade of the soldering iron tip close to the solder joint, and keep the soldering iron at an angle of about 60° to the horizontal plane so that the molten tin can flow smoothly from the soldering iron tip to the solder joint. The time the soldering iron tip stays at the solder joint should be controlled to 1-2 seconds;
3. Make sure that the insulator is not burned, the tin on the solder joint is smooth, burr-free, and there is no cold solder joint, and the definition of the solder wire meets the requirements of the drawing. -
3. What is a circular connector
A circular connector is a cylindrical electronic connector with a circular mating surface. It belongs to the fifth category of the interconnection classification and is mainly used for interconnection between devices. The design of circular connectors includes many types, such as low-frequency circular connectors, RF coaxial connectors and audio connectors, etc., with a wide operating temperature range from -55℃ to +150℃.
-
4. How to remove the circular plastic terminal head
1. Use scissors or flat-nosed pliers to cut off or remove the outer shell on the circular plastic terminal head to expose the internal wiring part.
2. Use a screwdriver to loosen the screws on the terminal head to remove the terminal head.
3. Gently pull the terminal head by hand to remove it from the wire.
4. If the terminal head is very tight, you can use flat-nosed pliers or pliers to increase the removal force.
5. If you need to replace a new terminal head, you can insert the new terminal head into the wire and tighten the screws to ensure that the wiring is firm.
